A user opts for doing a Netgear AC1200 extender reset in various scenarios. A few of them are a patchy or no internet connection, the extender’s non-working status followed by a firmware update, red light on the extender, and so on. Well, the list is so long. That is why, let’s directly shift our focus to the methods of resetting the range extender. But, before proceeding, we want to make you familiar with the fact that no matter what approach you choose to reset the extender, you must perform the Nighthawk extender setup again as soon as the device resets.
Methods to Netgear AC1200 Extender Reset
Two methods that can assist you to restore your WiFi range extender to its factory-set settings are as follows:
- Soft Reset Method: This method demands you to access the login portal of the range extender and delete the customized settings after reaching the extender’s dashboard.
- Hard Reset Method: In this method, the user only needs to push a button located on the hardware of the extender. Due to this fact, 90% of users go with this method.
Netgear AC1200 Extender Reset via Soft Reset Method
This section will shed light on the step-by-step instructions to be followed to get the extender restored to its default factory settings. Make sure you follow them carefully. Any carelessness during the process might stop you from resetting the device.
- Connect the Extender and Router
After powering up the range extender, you are supposed to join it to the router. An Ethernet cable will come in handy for this purpose. So, create a finger-tight connection between both devices. However, while doing so, be very sure that the cable opted by you is damage-free.
- Access mywifiext.net
The next step to do a Netgear AC1200 extender reset is to access the extender’s default web address. So, load an internet browser on your computer and reach the address bar. Type mywifiext.net and press the Enter key. You have to use mywifiext.local in case you are resetting the extender using an iOS device.
- Log in to the Extender
As soon as you access mywifiext.net, you will be taken to the extender’s admin portal. Now, enter the valid password and username of your AC1200 range extender into the provided fields and hit Log In. Keep in mind that the login info of the device is case-sensitive. Thus, you are not allowed to capitalize letters unnecessarily.
- Restore to Default Settings
You will now see the Netgear Genie dashboard. Select the Settings option. After that, click Other Settings to make your way to the window with the same label. Once you reach there, look for the Reset option and click it. A confirmation window will show up. Confirm your selection and let your extender get restored to the default factory mode.
In this way, you can reset your AC1200 extender. But as we said earlier, you have to set up the extender again after a factory reset, consider using the Nighthawk app or accessing the web management panel to configure the device. You are also free to take the assistance of the WPS method if your router is WPS-authorized. Just in case you are unable to reset the extender via the Soft Reset approach, using the Hard Reset method is suggested.
Netgear AC1200 Extender Reset via Hard Reset Method
- Power Up the Extender
Power up the range extender using a working wall outlet. You must know that any fluctuation in power can halt the reset process and there’s a possibility that your extender will deny working due to unpredictable pauses in the reset process. Therefore, consider using a UPS if your area suffers power outages a lot.
- Disconnect Your WiFi Devices
While you do the Netgear AC1200 extender reset via the Hard Reset method, there’s no need to connect the extender and router. Therefore, discard every connection related to the extender except the power cable. Wireless connections should also be cut down for a short while during the hard reset of the extender.
- Find and Press Reset
The last and final step in the hard reset method is to find and push the Reset button on the extender. Therefore, do the honors as soon as possible. In case you are skeptical about the location of the Reset button on the AC1200 extender, consider checking out the user manual. It consists of all the information you need about your product. You are required to hold the reset button for a few moments. Your extender will reset.
Summing Up
Here, we wrap up the guide focused on the Netgear AC1200 reset process. We hope that you have successfully reset your range extender to the default factory mode using any of the methods shared above.
